
Pull the trigger on your MIG welder and nothing happens. Or maybe the wire starts feeding, stutters for a few seconds, then stops completely. Sometimes you open the feeder compartment and find a tangled mess of wire wrapped around the drive rolls.
We've seen all of these problems, and the good news is that most wire feed issues aren't caused by a failed welding machine. More often than not, something is wrong between the wire spool and the contact tip. It could be a slipping drive roll, a spool brake that's too tight, a dirty gun liner, or a contact tip that's worn out or blocked.
The trick is knowing where to look. Replacing parts at random or cranking up the drive roll pressure usually wastes time and can make the problem worse. There's a much better way to troubleshoot a wire feeder, and it starts with following the wire through the machine, one component at a time.
At Link Technical Arc Services, we're an authorized service and repair centre for Lincoln Electric, Miller, ESAB and Forney in Canada, as well as an Approved Warranty Centre with factory trained technicians. We work on wire feed problems at our Concord repair shop every week, from small 140-amp home-shop MIG welders to industrial suitcase feeders connected to engine drives. Some repairs take a simple adjustment. Others require electrical troubleshooting or replacement parts.
We also provide free diagnostics, whether you bring your welding machine to our shop or we come to your location onsite.
Before booking a repair, though, there are several checks you can make yourself. Here's how we'd approach a MIG wire feed problem in the shop.
When someone calls and tells us their MIG welder isn't feeding wire, the first thing we ask is what exactly happens when they pull the trigger.
That matters because a feeder that doesn't move at all is a very different problem from one that runs but keeps slipping. And a machine that birdnests every few minutes needs a different approach than one that burns the wire back into the contact tip.
Here are the symptoms we hear about most often:
Pay attention to when the problem happens, too. Does it feed fine when the gun cable is straight but stop when you bend it? Does the motor run at lower wire speeds but struggle at higher settings? Does it only happen after welding for a while?
Those small details tell us a lot. Write them down before you start taking anything apart. If the machine eventually comes into our shop, that information can save a considerable amount of diagnostic time.
One of the simplest ways to diagnose a MIG wire feeder is to follow the actual path the wire takes.
It starts at the spool, passes through the spool brake and drive rolls, travels through the inlet and outlet guides, continues through the gun liner, and finally exits the contact tip into the arc.
That's the entire route: spool, spool brake, drive rolls, inlet and outlet guides, gun liner, contact tip, arc.
Every mechanical wire feeding problem involves something along that path. If the wire is being restricted at one point, everything behind it has to work harder to push it through.
We generally start at the spool and work toward the gun. It's a systematic approach, and it prevents unnecessary parts replacement.
Before making adjustments, switch off the machine and follow the manufacturer's safety instructions. Disconnect power before removing components or opening covers. When jogging wire for a test, keep the gun pointed away from yourself and anyone nearby, and keep your hands clear of moving drive rolls and the exposed wire.
Start with the wire spool. It's an easy component to overlook because there isn't much to it, but an incorrectly adjusted spool brake can cause surprisingly frustrating feeding problems.
The spool brake, also called hub tension, controls how freely the wire spool rotates.
If it's too tight, the drive motor has to work harder just to pull wire off the spool. You may notice jerky feeding, slipping drive rolls, or a motor that sounds like it's struggling.
If it's too loose, you've got the opposite problem. When you release the trigger, the spool keeps spinning even though the feeder has stopped. Loose wire builds up around the spool, and eventually you can end up with a birdnest.
You want just enough braking force to stop the spool when feeding stops, without creating unnecessary resistance while feeding.
If you're unsure about the current adjustment, back off the brake and gradually increase the tension while jogging the wire. Watch how the spool behaves when you stop. It should come to a stop without freewheeling.
Now take a close look at the welding wire itself.
Rust is a big one. We've seen plenty of MIG wire that's been sitting in a damp shop for months, and although the outside of the spool might look acceptable, the wire underneath can be contaminated.
As rusty or dirty wire travels through the gun, it leaves debris inside the liner. Over time, that buildup increases friction until the feeder starts slipping or stops altogether.
Check the wire diameter as well. The common MIG sizes are .030, .035 and .045 inch. Your drive rolls, guides, liner and contact tip all need to match the wire you're using.
For example, trying to push .045 wire through a .035 contact tip will cause a jam. Running .030 wire through a .045 tip can produce inconsistent feeding and burnback.
It's a simple mismatch, but it happens more often than you'd think, especially in shops where several people use the same machine and frequently switch between wire sizes.
Drive rolls are one of the first places we inspect when a MIG welder comes in with feeding problems.
They're also one of the most commonly misadjusted components on a wire feeder.
When the wire slips, the natural reaction is to tighten the pressure arm. Sometimes that helps. But if the actual problem is a blocked liner or the wrong drive roll groove, tightening the rolls can do more damage than good.
Check the groove first.
Drive rolls aren't interchangeable between every wire type. The groove profile matters just as much as the wire diameter.
Solid MIG wire normally uses a smooth V-groove. Flux-cored wire uses a knurled groove designed to grip the softer tubular wire without crushing it. Aluminium wire requires a U-groove to support the soft wire and prevent deformation.
Install the wrong type and you can end up with wire slipping, flattening, or being shaved as it passes through the feeder.
We've seen this happen after someone switches from solid wire to flux-cored wire without changing the drive rolls. The machine may still feed, but not consistently.
Check for wear.
Drive rolls don't last forever. After enough use, their grooves wear down and lose the ability to grip wire properly.
Look for a polished surface, an excessively worn groove, or a noticeable buildup of copper-coloured dust around the feeder.
That dust is worth paying attention to. Fine wire shavings often indicate excessive pressure or a groove that isn't suited to the wire being used. The shavings don't just stay around the drive rolls, either. Some eventually work their way into the gun liner and cause more feeding resistance.
Set pressure last, not first.
Drive roll pressure should be only tight enough to push the wire through without slipping.
Not as tight as possible. Just tight enough.
Too little pressure allows the drive rolls to spin while the wire stays in place. Too much pressure can flatten or deform the wire, create metal shavings, contaminate the liner, and lead to birdnesting or burnback.
For reference, Lincoln's service manual for the POWER MIG 350MP gives a normal tension arm setting of 1 to 1-1/2. That's specific to that model, though. Don't assume the same setting applies to another Lincoln feeder or a different manufacturer's machine.
Here's a practical test we use when checking the feed path.
Remove the contact tip, straighten the gun cable as much as possible, and jog the wire. Start with a lower drive roll pressure and increase it gradually until the wire feeds consistently without leaving deep marks.
If the drive rolls keep slipping even with the tip removed, inspect the rolls and everything upstream.
If the wire feeds smoothly without the tip but starts giving trouble when the tip is installed, you've narrowed the problem to the downstream path, including the tip, liner or gun cable.
Whatever you do, don't use excessive drive roll pressure to force wire through a blocked liner or an undersized contact tip. You'll usually end up with damaged wire, more debris in the liner, and another feeding problem shortly afterwards.
Between the wire spool and the gun liner, you'll find small guide tubes that keep the wire properly aligned as it travels through the drive rolls.
They don't look particularly important. They are.
An inlet guide that's the wrong size can allow the wire to move out of alignment. A worn outlet guide can catch the wire as it leaves the drive rolls. Either problem can create enough resistance to cause slipping or birdnesting.
On some machines, the inner guide is made from plastic and wears with use.
Lincoln's POWER MIG 350MP service manual specifically identifies a worn inner guide, along with a gun liner that isn't fully seated against the guide, as possible causes of wire birdnesting during welding.
Inspect both guides for cracks, excessive wear, and openings that have become oval instead of round. Make sure the guides are sized correctly for the wire.
Also check where the liner meets the outlet guide.
There shouldn't be a gap between them. If the liner hasn't been pushed fully into position, the wire can catch as it moves from the feeder into the gun.
That small gap is enough to create repeated wire jams, particularly when using softer wire.
If there's one component we end up replacing regularly on MIG guns with feeding problems, it's the liner.
The liner runs inside the gun cable and guides the welding wire from the feeder all the way to the contact tip. Every time you weld, wire is sliding through it.
Eventually, it wears out.
A liner can become restricted for several reasons. Copper flakes from the wire, dust from the feeder, rust, and small metal shavings gradually collect inside it. As the debris builds up, the wire becomes harder to push through.
Sometimes the issue isn't dirt at all.
We've inspected guns where the cable had been run over by equipment, crushed under a heavy object, or repeatedly bent into a tight loop. That can kink the liner inside the cable, creating a restriction you won't necessarily see from the outside.
Heat and age can also cause a liner to soften or collapse. And, of course, using a liner that's too small for the wire will create feeding problems from the start.
Here's how to check it.
With the machine safely switched off and isolated, remove the contact tip. If the gun design allows it, disconnect the gun from the feeder. Then try pulling the welding wire through the liner by hand.
You should feel very little resistance.
If the wire catches, drags, or becomes noticeably harder to pull, the liner deserves a closer look.
We generally try cleaning it first when the liner is otherwise in good condition. Use low-pressure compressed air to blow out the accumulated dust and debris, following the gun manufacturer's instructions and wearing suitable eye protection.
If cleaning doesn't improve the feeding, replace the liner.
Liners are relatively inexpensive compared with other welding machine components, and replacing one often solves a problem that someone has spent hours trying to correct with drive roll adjustments.
In our shop, when a production MIG machine has been using the same liner for a year or more and starts feeding erratically, that liner is one of the first things we suspect.
There's another test worth doing before you put everything back together.
Look at the way the gun cable sits while you're welding.
A gun cable hanging over the edge of a workbench, wrapped around equipment, or coiled tightly on the floor creates additional wire resistance. The machine might feed perfectly with the cable laid straight on a bench, then start stuttering when you move back to your normal welding position.
We've seen this exact situation. Nothing was wrong with the feeder motor. The cable routing was creating the restriction.
Keep the gun cable as straight as practical, and avoid unnecessary sharp bends.
Before spending money on a new gun liner or drive rolls, inspect the contact tip.
It's a small, inexpensive consumable, but it can cause a surprising number of wire feed issues.
The contact tip is the last component the welding wire passes through before entering the arc. It also transfers welding current to the wire, so it's exposed to heat, wear, and spatter.
Over time, the opening can become worn and oval. Spatter can build up around it, or the wire can burn back and fuse directly into the tip.
Once that happens, the wire can't travel smoothly.
Start by confirming the correct size. If you're using .035 wire, you need a .035 contact tip.
Remove the tip and inspect it closely. Look for an enlarged or uneven opening, spatter buildup, heat discolouration, or wire fused inside the bore.
If the wire doesn't slide through smoothly by hand, replace it.
We don't recommend spending much time trying to salvage a badly worn or blocked tip. It's a consumable, and installing a fresh one is usually the quickest way to eliminate it as a possible cause.
While the tip is removed, inspect the nozzle and gas diffuser too.
Heavy spatter inside the nozzle can interfere with the wire, and a damaged diffuser may prevent the contact tip from sitting properly centred.
A quick inspection of these components can save you from taking apart the entire feeder unnecessarily.
So far, we've focused on problems that physically stop the wire from moving.
But what if you pull the trigger and the drive rolls don't turn at all?
Now we need to consider an electrical fault.
The gun trigger sends a control signal to the welding machine to start the feeding sequence. If the trigger switch fails, a control wire breaks, or the gun connector develops a poor connection, the feeder may not respond even though the power source turns on normally.
This is particularly common on welding guns that get dragged across a shop floor, pulled around structural steel, or caught between equipment.
The outside of the cable can look fine while a small control wire inside has been damaged.
Before assuming the feeder motor or control board is defective, check the gun connection.
Make sure the gun plug is properly seated and look for obvious damage to the trigger and cable.
If the machine has a wire jog or inch function, try it.
When the wire feeds using the jog function but refuses to feed when you pull the gun trigger, that points toward the trigger circuit or its connections.
If neither the trigger nor the jog function operates the motor, the problem may be further inside the feeder.
There's an important distinction here: if you can hear the motor running and see the drive rolls turning, you're probably dealing with a mechanical feeding problem. If the motor doesn't operate at all, the electrical controls need to be investigated.
At that stage, don't start bypassing switches or connecting wires together to see what happens. A proper electrical diagnosis is safer and can prevent damage to the control board.
Not every wire feed problem is caused by a liner, contact tip, or drive roll.
Sometimes we receive a machine with a perfectly clean wire path, correctly adjusted tension, and a good gun, but the feed motor still doesn't operate properly.
That's when we start looking at the feeder's electrical components.
Wire feed motors can fail. Depending on the machine's design and age, the problem may also be in the motor drive circuit or control board.
One symptom we sometimes encounter is a feeder that works at lower wire speed settings but starts cutting out when the speed is increased.
Another is a feeder that operates normally when the machine is cold, then becomes intermittent as the equipment warms up.
Those symptoms can point to an electrical problem, although they don't prove that the motor or board has failed.
Proper diagnosis requires checking the relevant control signals, motor operation, and circuitry against the manufacturer's service information.
This isn't work we'd recommend attempting without the appropriate electrical training and test equipment. Even after a welding machine is switched off, internal components can retain dangerous voltage.
And guessing at a circuit board fault can become expensive very quickly. Replacing an entire board when the actual issue is a connection or motor problem is an unnecessary repair.
If you've checked the spool, drive rolls, guides, liner, contact tip, and gun connections and the feeder still won't operate correctly, it's time to have the machine professionally diagnosed.
Before bringing it in, make a note of whether the motor runs, whether any fault codes appear, and whether changing the wire speed affects the problem.
That information gives the technician a useful starting point.
If you're standing in front of a MIG welder that won't feed wire, here's the order we'd recommend checking things.
Don't change five adjustments at once. Make one change, test the machine, and move to the next step only if the problem remains. Otherwise, you won't know what actually fixed it.
Most mechanical feeding problems can be narrowed down by following these steps. And if the machine eventually needs a repair, you'll already have ruled out the common consumable and adjustment issues.
One of the biggest differences between a quick repair and a long troubleshooting job is the information we receive with the machine.
We've had welding machines dropped off with nothing written on the tag except "wire doesn't work."
That doesn't give a technician much to go on.
A little more detail can make a big difference, particularly with intermittent problems that may not appear immediately during testing.
Here's what we'd like to know:
We also recommend bringing the gun and the actual wire spool you've been using.
This is especially helpful with intermittent feeding problems. A machine might feed perfectly when we connect one of our shop guns, but fail again when the customer's original gun is installed.
The same applies to contaminated wire or an incorrectly adjusted spool.
Testing the machine with the components that were installed when the problem occurred gives us a much better chance of reproducing the fault.
Most MIG wire feeder repairs aren't particularly complicated once the actual cause has been identified.
In many cases, we're replacing a worn gun liner, installing the correct drive rolls, fitting a new contact tip, repairing or replacing a wire guide, or adjusting the spool brake.
Trigger switches and damaged gun control leads are also common repairs.
These are generally more straightforward jobs than diagnosing a failed feed motor or electronic control board.
When the problem is inside the feeder's electrical system, the repair can become more involved. We may need to test the motor, wiring, connectors, and associated control circuitry before determining which component has failed.
On an older welding machine, repair cost also becomes part of the decision.
A machine that's otherwise in good condition may be worth repairing even if the feeder requires a major component. On the other hand, if the repair cost is approaching the value of the equipment, replacing the machine might make more financial sense.
We discuss that decision in more detail in our guide to repair vs replace a welding machine.
If you're trying to understand what different repairs typically cost in the GTA, our welding machine repair cost in Toronto guide explains the usual price ranges. Those figures are intended as general ranges, not repair quotes, because the actual cost depends on what has failed and which parts are required.
At Link Technical Arc Services, diagnostics are free whether you bring the machine to our Concord shop or arrange an onsite visit.
We'll inspect the equipment, identify the problem, and provide an estimate before proceeding with the repair. That way, you can decide whether fixing the machine makes sense without paying just to find out what's wrong.
Birdnesting happens when the drive rolls continue pushing welding wire but the wire can't move freely through the gun. Instead of travelling forward, it buckles and creates a tangled mess around the feeder.
The most common causes are a blocked or worn contact tip, a dirty or kinked gun liner, excessive drive roll pressure, a spool brake that's too loose, or a worn wire guide.
Start by clearing the tangled wire with the machine safely switched off. Then inspect the contact tip and liner before adjusting the drive roll pressure.
One mistake we see regularly is someone tightening the drive rolls after the first birdnest. If the wire is already being blocked downstream, more pressure only pushes harder against the restriction and makes another birdnest more likely.
Burnback occurs when the welding arc consumes wire faster than the feeder is delivering it. Eventually, the wire melts back and fuses into the contact tip.
A worn or incorrectly sized contact tip is one possible cause. Other common problems include excessive friction inside the gun liner, a sharply bent gun cable, or drive rolls that slip under load.
Remove the contact tip and straighten the gun cable, then jog the wire to check whether it feeds smoothly.
If feeding improves with the tip removed, install a new tip that matches your wire diameter.
If it still drags, inspect the liner and drive rolls. Don't keep replacing contact tips without correcting the feeding problem, or you'll likely experience the same burnback again.
Only tight enough to feed the welding wire consistently without slipping.
Too little drive roll pressure means the rolls spin while the wire stays in place. Too much pressure can flatten the wire, shave off material, and contaminate the gun liner. That additional debris can eventually cause birdnesting or burnback.
A practical way to set the pressure is to remove the contact tip, keep the gun cable straight, and jog the wire while increasing tension gradually.
Once the wire feeds steadily without leaving deep marks, stop tightening.
Remember that the correct pressure setting depends on the machine, feeder design, and wire type. Always refer to your manufacturer's manual rather than copying a tension setting from another welder.
There's no fixed replacement interval that applies to every MIG gun. Liner life depends on how often the machine is used, the condition of the welding wire, the type of wire being fed, and how the gun cable is handled.
In a production shop where the machine runs daily, a liner that's been in service for a year or more is one of the first components we'd inspect when wire feeding becomes inconsistent.
If you can feel noticeable resistance when pulling the wire through by hand, the liner may be dirty, damaged, or worn.
Try cleaning it with low-pressure compressed air. If the wire still doesn't travel smoothly, replace the liner.
It's a relatively inexpensive part, and a new liner can eliminate several possible feeding problems at once. Just make sure you install the correct liner for your gun and wire diameter.
If your MIG wire feeder still isn't feeding properly after going through these checks, book a free diagnostic with Link Technical Arc Services.
Bring the welding machine, gun, and wire spool you've been using, along with a description of the symptoms. The more accurately we can reproduce the problem, the faster we can get to the cause.
Our technicians service and repair MIG, TIG and stick welders, plasma cutters and engine-driven welding machines throughout Toronto and the GTA. You can read more about the equipment we work on through our welder repair service page.
Dealing with a different welding machine problem? We've also put together a guide covering 12 common causes of a welding machine not welding, along with specific troubleshooting advice for a Miller welder that won't strike an arc.
If your machine powers up normally but produces no welding output, take a look at our article explaining why a welding machine turns on but has no output.
You'll find more practical welding machine troubleshooting and repair information on our blog.